Ninja / Musket / Psychoblasters V2. Getting Started. Let's start by locating our relay. The relay is a small black (or red) box with four terminals that protrude from the bottom of the box. Each terminal on the bottom of the relay corresponds to a nu

Ninja / Musket / Psychoblasters V2<hr>Getting StartedLet&apos;s start by locating our relay. The relay is a small black (or red) box with four terminals that protrude from the bottom of the box.&#xA0;<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-baea65fc-cb2f-4641-b346-0268e5d5b0dc" style="width: 350px;" class="fr-fic fr-dii"><img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-70d33829-f4c1-47d9-9c5c-1c0a397c3df4" style="width: 550px;" class="fr-fic fr-dib fr-fil"> Each terminal on the bottom of the relay corresponds to a number. You can reference back to these numbers when looking at a relay wiring diagram. All of our relays are laid out in the same fashion as above. If the numbers on your relay cannot be read, you can reference the following diagram for the pin out. <img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-9728d52c-4b3f-4da3-b6c0-5fc4723b7e78" style="width: 350px;" class="fr-fic fr-dii"><hr>Wiring The RelayThis is one of the trickiest parts of the install, and rightfully so. If the relay is not wired exactly right, the horn will not make any sound.<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-d9560ab8-abed-4f64-90a3-c841509ba33b" style="width: 636px;" class="fr-fic fr-dib fr-fil">The diagram above shows how the direct-drive compressor can be connected to a push-button.<hr>Each number on the diagram corresponds to each pin on our relay as we mentioned above. We will be using Female Quick Disconnects to complete these connections. Each connector looks like the following: <img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-1d7dd92c-a488-4f80-a9c9-b30c9555ff78" style="width: 300px;" class="fr-fic fr-dii"> We will use this connector for terminals 85 and 86.Pin 30Pin 30 will connect to the positive terminal of our car battery. For this connection, we will be using the red (10ga) wire that came with your kit. We will also use the fuse holder here as well.Our fuse-holder is sent to you in a loop. *Do not install a fuse into the holder yet.<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-d6f3ec1f-bfe6-4d33-95b9-01f3e118d661" style="width: 175px;" class="fr-fic fr-fil fr-dib">Go ahead and cut the fuse holder in the center to make two ends. You can cut the wire where the dashed line is in the picture above. Using a set of wire strippers, strip each end of the holder and expose the copper leads. Each end should now look like this:<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-a51266dc-cdf6-4de2-8881-a8d855b0d3a5" style="width: 150px;" class="fr-fic fr-dii">At this point, we will use the supplied ring terminal crimp connector on one side of this fuse holder. The opposite end of the fuse holder will accept one of the yellow butt connectors included with the electrical connectors. The two connectors are pictured below.<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-55c4f8c0-9453-4410-994f-614e323ff83e" style="width: 100px;" class="fr-fic fr-dii"> <img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-2471362e-b4e5-46ef-8a46-11fe04b5cd58" style="width: 50px;" class="fr-fic fr-dii">The ring terminal connector can be used to connect the fuse holder to your positive battery terminal. The yellow connector will allow us to connect the fuse holder to our red wire, and complete the connection back to the relay. Go ahead and strip one end of the supplied red wire, and connect it into the opposite end of the yellow butt connector. Route your red wire from the fuse holder back to the relay. Do not cut your red wire until you have finished routing it back to the relay. You want to make sure you have enough before you cut it short.Once the red wire has been routed back to the relay, you can cut off any excess wire while still leaving a small amount of slack. Now, l<span style="color: rgb(65, 65, 65); font-family: sans-serif; font-size: 14px; font-style: normal; font-variant-ligatures: normal; font-variant-caps: normal; font-weight: 400; letter-spacing: normal; orphans: 2; text-align: left; text-indent: 0px; text-transform: none; white-space: normal; widows: 2; word-spacing: 0px; -webkit-text-stroke-width: 0px; background-color: rgb(255, 255, 255); text-decoration-thickness: initial; text-decoration-style: initial; text-decoration-color: initial; display: inline !important; float: none;">ocate the neon green terminal connector in your electrical kit.&#xA0;<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-1f01b07f-8766-4459-b541-ea5ff0daacc9" style="width: 118px;" class="fr-fic fr-dii">This connector will allow you to connect our 10ga red wire to the relay. Slide the connector over pin 87, but do not crimp the connector yet. We will add another small wire here later.<hr>Pin 87Pin 87 is the easiest connection to complete with this setup. Connect a lead of red wire from the positive terminal on the direct-drive compressor and connect it directly to pin 87 on your relay. You will use two more of the light-green connectors above.<hr>Pin 85Pin 85 is a ground connection for the relay. This pin will get routed over to the frame of the vehicle as a ground with our push button in between. The red terminal connector will simply slide over the pin on the relay, and you may crimp an exposed lead of 18ga wire into the connector. We will be using our push button in between the relay and the ground point, to make and break the ground connection. This in turn will allow the relay to turn on/off as you press the button. Take one lead of the button to pin 85 on the relay, and the opposite lead of the button to the desired ground point.<hr>Pin 86Pin 86 will connect to pin 30, using 18ga wire. You can strip the end of the grey or blue wire and connect it into the same crimp connector your red wire is connected into. Once both leads are in the connector, go ahead and crimp the wires into it. Crimp the opposite end of the blue/grey wire into the terminal connector on pin 86.<hr>At this point, your relay is wired and can be tested. Insert one of the supplied 35A fuses into the fuse holder and press your horn button. The compressor should start to make a whirring sound, indicating that it is pushing air. If it sounds like it is grinding, check the connections at the compressor itself. This usually happens if the positive/negative connections are backward.&#xA0;

Wiring up the Ninja, Musket, & Psychoblasters V2

Motorcycle / Truck Horns. Getting Started. Let's start by locating our relay. The relay is a small black (or red) box with four terminals that protrude from the bottom of the box. Each terminal on the bottom of the relay corresponds to a number. You

Motorcycle / Truck Horns<hr>Getting StartedLet&apos;s start by locating our relay. The relay is a small black (or red) box with four terminals that protrude from the bottom of the box.&#xA0;<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-baea65fc-cb2f-4641-b346-0268e5d5b0dc" style="width: 350px;" class="fr-fic fr-dii"><img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-e2a3aa10-ae91-4781-8311-396dc8bcde62" style="width: 472px;" class="fr-fic fr-dib fr-fil"> Each terminal on the bottom of the relay corresponds to a number. You can reference back to these numbers when looking at a relay wiring diagram. All of our relays are laid out in the same fashion as above. If the numbers on your relay cannot be read, you can reference the following diagram for the pin out.<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-a588ffef-04f0-4e08-ae30-59139d5210ff" style="width: 373px;" class="fr-fic fr-dib fr-fil"><hr>Wiring The RelayThis is one of the trickiest parts of the install, and rightfully so. If the relay is not wired exactly right, the horn will not make any sound.<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-c6af5777-bbcc-4e3f-8b05-35121783d497" style="width: 812px;" class="fr-fic fr-dib fr-fil"> The diagram above shows how the direct-drive compressor can be connected to a push-button.<hr>Each number on the diagram corresponds to each pin on our relay as we mentioned above. We will be using Female Quick Disconnects to complete these connections. Each connector looks like the following: <img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-1d7dd92c-a488-4f80-a9c9-b30c9555ff78" style="width: 300px;" class="fr-fic fr-dii"> We will use this connector for terminals 85 and 86.Pin 87Pin 87 will connect to the positive terminal of the car battery. For this connection, we will be using the red (10ga) wire that came with your kit. We will also use the fuse holder here as well.Our fuse-holder is sent to you in a loop. *Do not install a fuse into the holder yet.<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-d6f3ec1f-bfe6-4d33-95b9-01f3e118d661" style="width: 175px;" class="fr-fic fr-dii">Go ahead and cut the fuse holder in the center to make two ends. You can cut the wire where the dashed line is in the picture above. Using a set of wire strippers, strip each end of the holder and expose the copper leads. Each end should now look like this:<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-6f59327c-4fc2-4bb9-b5a2-091fae3ab37b" style="width: 112px;" class="fr-fic fr-dib fr-fil"> At this point, we will use the supplied ring terminal crimp connector on one side of this fuse holder. The opposite end of the fuse holder will accept one of the yellow butt connectors included with the electrical connectors. The two connectors are pictured below.<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-55c4f8c0-9453-4410-994f-614e323ff83e" style="width: 109px;" class="fr-fic fr-dii"> <img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-2471362e-b4e5-46ef-8a46-11fe04b5cd58" style="width: 50px;" class="fr-fic fr-dii">The ring terminal connector can be used to connect the fuse holder to your positive battery terminal. The yellow connector will allow us to connect the fuse holder to our red wire, and complete the connection back to the relay. Go ahead and strip one end of the supplied red wire, and connect it into the opposite end of the yellow butt connector. Route your red wire from the fuse holder back to the relay. Do not cut your red wire until you have finished routing it back to the relay. You want to make sure you have enough before you cut it short.Once the red wire has been routed back to the relay, you can cut off any excess wire while still leaving a small amount of slack. Now, l<span style="color: rgb(65, 65, 65); font-family: sans-serif; font-size: 14px; font-style: normal; font-variant-ligatures: normal; font-variant-caps: normal; font-weight: 400; letter-spacing: normal; orphans: 2; text-align: left; text-indent: 0px; text-transform: none; white-space: normal; widows: 2; word-spacing: 0px; -webkit-text-stroke-width: 0px; background-color: rgb(255, 255, 255); text-decoration-thickness: initial; text-decoration-style: initial; text-decoration-color: initial; display: inline !important; float: none;">ocate the neon green terminal connector in your electrical kit.&#xA0;<img src="https://uploads.gorgias.io/mJQz875pXo2adpn4/undefined-1f01b07f-8766-4459-b541-ea5ff0daacc9" style="width: 118px;" class="fr-fic fr-dii">This connector will allow you to connect our 10ga red wire to the relay. Slide the connector over pin 87. Do not crimp the connector yet. We will add another small wire here later.<hr>Pin 30Pin 30 is the easiest connection to complete with this setup. Connect a lead of red wire from the positive terminal on the direct-drive compressor and connect it directly to pin 87 on your relay. You will use two more of the light-green connectors above.<hr>Pin 85Pin 85 is a ground connection for the relay. This pin will get routed over to the frame of the vehicle as a ground with our push button in between. The red terminal connector will simply slide over the pin on the relay, and you may crimp an exposed lead of 18ga wire into the connector. We will be using our push button in between the relay and the ground point, to make and break the ground connection. This in turn will allow the relay to turn on/off as you press the button. Take one lead of the button to pin 85 on the relay, and the opposite lead of the button to the desired ground point.<hr>Pin 86Pin 86 will connect to pin 30, using 18ga wire. You can strip the end of the grey or blue wire and connect it into the same crimp connector your red wire is connected into. Once both leads are in the connector, go ahead and crimp the wires into it. Crimp the opposite end of the blue/grey wire into the terminal connector on pin 86.<hr>At this point, your relay is wired and can be tested. Insert one of the supplied 35A fuses into the fuse holder and press your horn button. The compressor should start to make a whirring sound, indicating that it is pushing air. If it sounds like it is grinding, check the connections at the compressor itself. This usually happens if the positive/negative connections are backward.&#xA0;

Wiring up your Electric Motorcycle Horn or Truck Horn

Can't find what you're looking for? Click the link above to send an email to our team of Horn Stars!

Give our team a call for additional help!

Home

Shop

Contact

Installation Guides

Troubleshooting

HornBlasters

Electric Horns

Conductors Special Kit Support

Air Filter Relocation

Preparing for your Install

Tank Assembly

Connecting Shocker Horns to the Air Tank

Installation: Wiring up your Pressure Switch

Connecting Our Horns to the Steering Wheel

Using A Push Button to Honk Your Horns

Conductors Special 232-244K Install Guides

How to: Install Electric Drain Valve Kit

How to: Install Tire Inflation Kit

How to: Install Dual Tank Electric Drain Valve Kit

How to: Install Digital Air Gauge

Installing the Tire Inflation Kit w/ a 2MC Kit

Accessories

Rebuilding Your K-Series Nathan Airchime

Horn Repair Guides

Using Air Bags / Load Support Bags with your Horn Kit (Single Path)

Air Suspension

Connecting the Train Horns to the OEM Horn (2004-2014 Ford F150)

Connecting the Train Horns to the OEM Horn (2015-2017 Ford F150)

Connecting the Train Horns to the OEM Horn (2021- Ford F150)

Connecting the Train Horns to the OEM Horn (2018-2020 Ford F150)

Connecting the Train Horns to the OEM Horn (2017+ Ford F250/350)

Connecting the Train Horns to the OEM Horn (2019-2021 Ford Ranger)

Ford

Connecting the Train Horns to the OEM Horn (2015-2020 GM/Chevy Truck/SUV)

Connecting the Train Horns to the OEM Horn (2014 Chevy Silverado)

Connecting the Train Horns to the OEM Horn (2001-2013 Chevy Silverado)

GM / CHEVY

Connecting the Train Horns to the OEM Horn (2016+ Tacoma)

Connecting the Train Horns to the OEM Horn (2007 FJ Cruiser)

Toyota

Tapping into OEM Horn

Wiring up the 2MC/127H/228H

Using HornBlasters horns in Buildings / Arenas

Toggle switch between two horns

Test a 40A Relay